Horizontal and vertical track repair for sectional doors. Bent rails are straightened or replaced, alignment is laser-checked, and brackets are re-anchored to spec.
Garage Door Track Repair is one part of our garage door repair coverage in Utah. For the full picture — symptoms, costs, and when to repair vs. replace — start with the complete Garage Door Repair guide, or browse every garage door repair service we offer.
Track repair covers the rails that guide the door's rollers from closed to fully open. Tracks bend from vehicle impact, twist from heavy door weight on under-spec rails, separate from masonry as anchors loosen, and rust from coastal exposure. A door with a damaged track doesn't roll smoothly — it binds, jumps the rail, or stops short. Track repair re-straightens, re-anchors, and where necessary replaces the bent section so the door tracks straight again.
We use a laser alignment tool to verify the track sits parallel to its mate within tolerance. Eyeballing tracks for plumb is unreliable; the laser catches twist and tilt that the eye misses. After alignment, brackets are re-anchored to manufacturer torque spec — under-torqued brackets are a slow-motion failure waiting to happen.
Bent sections that can't be straightened are replaced from stock. We carry 2-inch and 3-inch tracks in galvanized steel and the bracket families for the major door brands. Most track repairs are completed in 60–90 minutes. Severely damaged tracks from major impact may require partial track replacement and a roller inspection (impact often damages the rollers and panel mounts simultaneously).
Signs you need garage door track repair
Door jumps the track on opening
Roller comes out of the channel mid-travel. Stop using the door — the next cycle could leave the door off-track entirely.
Visible bend or kink in the track
Vehicle impact, ladder strike, or shelf collapse against the track all cause visible bends. Repair before continued operation.
Track misalignment or roller bind causes audible scraping. Often easy to fix in the early stage; expensive to fix after the rollers also damage.
Track separating from wall
Brackets pulling loose from masonry or framing show as gaps between the track and the wall. Re-anchor before track shifts further.
Door uneven side-to-side
If one side of the door is higher than the other when fully closed, one track may have settled or shifted.
Common causes & what we fix
Vehicle impact
Backing into the door or sliding the car into the open track is the most common cause of bent rails. Often comes with associated panel damage.
Bracket anchor failure
Anchors pull from masonry or framing over years of cycle vibration. Re-anchoring to fresh holes restores hold.
Rust through
Coastal corrosion eats through track bottom where water pools. Replacement section with galvanized track stops the progression.
Under-spec track for door weight
Builder installs occasionally pair light-gauge track with heavy doors. The track flexes over time and develops bend.
Settling building
Foundation movement shifts walls and the brackets that anchor to them. Tracks twist as a result.
Our process
1
Call or schedule online. Start your garage door track repair request by phone or online. Pick a 2-hour window; a five-minute confirmation follows with the tech's name and photo.
2
On-site diagnosis. We diagnose your garage door track repair in person, show you exactly what's wrong, and only then quote it. Most repairs are diagnosed free; minor service calls carry a $39 fee, waived if you proceed.
3
Flat-rate quote. You approve a flat-rate, written garage door track repair quote first. No hourly creep, no pressure — our salaried (not commissioned) techs have no reason to oversell.
4
Same-visit fix. We aim to finish your garage door track repair on the first visit, and 96% of the time we do. The job ends with a test cycle you watch and a full clean-up of the work area.
How much does garage door track repair cost in Utah?
Garage Door Track Repair the United States starts at from $159, and the garage door track repair number is flat-rate, written, and set before we begin — no hourly billing, no surprise parts charges. We discount labor 10% for seniors (65+) and military, and projects over $1,500 can use 0% APR Synchrony financing for 12 months with no prepayment penalty.
Why homeowners in Utah choose us for garage door track repair
We've been a trusted choice since 1974 — over 50 years of family-owned garage door service across Utah. Our techs are CSLB-licensed (#1098234), background-checked, and complete an internal 12-week training program before rolling on calls alone.
The garage door track repair carries a decade-long workmanship guarantee — independent of the manufacturer's parts warranty. Fail because of how we installed it, and we fix the garage door track repair at no cost for ten years. 30,000-cycle springs hold a lifetime warranty for the original homeowner, with parts and accessories backed 1–5 years by item.
Honest sizing and honest scope drive how we quote garage door track repair: we don't up-sell unnecessary work, our techs are salaried (not commissioned), and the diagnostic is structured so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. Either way the garage door track repair quote is flat-rate, written, and good for 30 days.
Areas we serve for garage door track repair
We provide garage door track repair throughout Utah, with fast coverage in every major Utah metro.
Because Utah traffic moves garage door track repair response times around, we quote your ETA live on the call rather than guessing. Our dispatch number connects to an on-call tech with no voicemail in the way.
Frequently asked about garage door track repair
Top questions homeowners searching for Garage Door Track Repair near me ask us:
Sometimes — mild bends in galvanized steel can be re-straightened with a track-press tool. Severe bends, kinks, and corroded sections need replacement.
Most jobs: 60–90 minutes. Full track replacement (rare): 2–3 hours. Includes alignment verification and a balance test.
Yes — we don't leave until the door cycles fully and smoothly with no binding. Photo-eye, force, and balance are all verified before we go.
Yes — new doors should always be paired with new tracks and brackets. Reusing old tracks is a false economy that limits the new door's life.
In coastal zones — yes, almost always. Inland — standard tracks are fine. We default to galvanized within 5 miles of the coast.